NEW LNS Quick Load Servo 80 S2 Magazine Bar Loader

General Specifications per Brochure:

Automatic Magazine Loader for short bars - Length of Spindle Feed Cap

For fixed or Bushingless Traveling Headstock Lathes
Ideal solution for 1-5/8", 2", 2-1/2", 3" bar capacity turning centers.
One model fits all!

Bar Diameter Capacity: 1/4" - 3-1/8"
Maximum Bar Length Capacity: 63" - not to exceed overall length of spindle
Minimum Bar Length Capacity: 14"
Control Voltage: Electrical control cabinet, including auto-transformer for
200 to 460 volts with 24 Vdc power supply
Changeover Time: 15 seconds changeover - enter bar diameter, part length,
shape and select set up mode - no mechanical changes required, 1 minutes
complete changeover
Approx Dims: 80" x 66" x 50"
Shipping Weight: 1,150 lbs.

PRICES SUBJECT TO CHANGE WITHOUT NOTICE

New Unit (includes): .........................................$21,390.00
1/4" through 3-1/8" diameter x 14" through 63" length bar capacity
3 Pushers with Bushings
1/4" through 1/2" diameter bar stock (6mm pusher)
9/16" through 1-1/4" diameter bar stock (12mm pusher)
1-5/16" through 3-1/8" diameter bar stock (20mm pusher)
X or Z axis retract
Custom Electrical Cable Package with Plugs

Note: The maximum bar length cannot exceed the combined length of the
headstock/actuator assembly.

OPTIONAL ACCESSORIES
Adapter kit for square bar stock, 6" or 12" long: .............$ 360.00
V-Channel extension & cover, 12" long: ........................$ 640.00
Safety cover for recessed spindles, 12" long: .................$ 250.00
Replaceable disk for tubing: ..................................$ 170.00
Tall Stands (1300 mm - 1500 mm): ..............................$1,340.00
One shot shaft loading to load 4" thru 14" round or hex
(Includes short parts kit, pusher and software): ............$4,815.00
Adapter kit to load 4" thru 14" round or hex stock: ...........$1,550.00
e-Connect interface capability: ........................consult factory
Dual Channel Safety Circuit Protection (DCS) ................. $535.00

STEEL SPINDLE LINERS -
Quick Load Servo 80 requires one spindle liner tube for each bar stock
diameter
Spindle Liner.............. ROUND.........HEX & SQUARE
Up to 3-1/8" Drawtube I.D.: $30.00.......$585.00
Surcharge for Hardened Liner:$350.00
Confirmation Ring: $270.00
Coolant Collector Extension: $700.00
Quick Change Adapter: $540.00

POLYURETHANE SPINDLE LINERS -
Quick Load Servo 80 requires one spindle liner tube for each bar stock
diameter
Up to 3-1/8" Drawtube I.D.:(round/hex)..........................$ 375.00
(Square).............................$ 510.00
(Custom).............................$ 960.00

INSTALLATION
Installation (USA) .............................................$2,950.00
Installation (Canada & Mexico) .................................$3,450.00

An LNS Service Engineer can be provided to install the bar feeder at a flat
rate; this is on a "per trip" basis. The standard installation includes set up
of the bar feeder, mechanical alignment, mounting the bar feeder to floor,
electrical connection of the bar feeder to the machine tool interface
(supplied by the builder), and a complete check and run off of the bar feeder.
A set of anchor bolts for the bar feeder is included. In order to allow
comprehensive training and run off, it is recommended that machine be set up
and capable of making parts; and part programs and material should be
available before arrival of the LNS Service Engineer.

STANDARD WARRANTY
Standard warranty includes one year parts and labor including travel.