| Tank-W | 12" |
| Tank-L | 18" |
| Tank-H | 16" |
| Number of Tanks | 3 |
| Transfer System? | No |
Tank Dimensions: 12" left to right by 18" front to back by 12" deep (10" liquid depth).
Overall Dimensions: 90" left to right by 32" front to back by 41" high.
Process: Wash, Rinse, Rinse, Dry. Chemistry: Deionized Water.
NOT MANUFACTURED FOR USE WITH ANY FLAMMABLE LIQUIDS.
Power Requirements: 240 volts/60 Hz/3 phase.
Work Flow: Left to Right
System Detail:
Station #1: Ultrasonic Immersion Wash
Maximum Temperature: 140 °F.
Ultrasonic Frequency: 40 kHz. Ultrasonic Power: 1000 watts of ultrasonic power provided by:
• Twelve (12) transducer modules direct-bonded to the bottom of the tank.
• One (1) Model CG-1000-40-T (part # 9510200) ultrasonic generator.
Heat: 3000 watts of strip heat. Temperature control: Capillary bulb-type thermostat. Recirculation / Filtration: A 5 GPM recirculation/filtration system with:
• One (1) wye strainer.
• One (1) centrifugal, mag-drive pump, with: o Ryton head. o Viton o-ring. o TEFC motor.
• One (1) 10", 10 micron cartridge filter housed in a stainless steel canister.
• Manual flow control valves.
Standard Features:
• A stainless steel lift off cover.
• A rear overflow weir plumbed to the recirculation system.
Station #2: Ultrasonic Immersion Rinse
Maximum Temperature: 120 °F.
Ultrasonic Frequency: 40 kHz.
Ultrasonic Power: 1000 watts of ultrasonic power provided by:
• Twelve (12) transducer modules direct-bonded to the bottom of the tank.
• One (1) Model CG-1000-40-T (part # 9510200) ultrasonic generator.
Heat: 2000 watts of strip heat. Temperature control: Capillary bulb-type thermostat.
Standard Features:
• A stainless steel lift off cover.
• A side-located overflow weir plumbed to drain.
Station #3 Ultrasonic Final Rinse
• Ultrasonic Frequency: 40 kHz.
Ultrasonic Power: 1000 watts of ultrasonic power provided by:
•Twelve (12) transducer modules direct-bonded to the bottom of the tank.
• One (1) Model CG-1000-40-T (part # 9510200) ultrasonic generator
Heat: 2000 watts of strip heat.
Temperature control: Capillary bulb-type thermostat.
Standard Features:
• A capillary bulb-type overtemperature safety thermostat.
• A stainless steel lift off cover.
• A side-located overflow baffle with cascade flow to Station #2
Station #4: Recirculating Hot Air Dryer
Maximum Temperature: 160 °F.
Heat 5000 watts of heat.
Temperature control: Digital indicating temperature controller with a RTD-type temperature probe.
Blower A 1000 CFM recirculating blower in the updraft orientation.
Cover: A manual sliding cover.
System Notes:
The general system specifications are as follows:
Tank Material: Type 316L stainless steel with a #2B finish.
Frame Material: Type 304 stainless steel support frame with leveling legs.
Access Panels: Type Epoxy Coated, lift-out access panels on all sides.
Countertop: A type 304 stainless steel, removable, countertop.
The countertop will be fitted with a 304 stainless steel, removable drainbacks (between the process stations).
Base Plate: A type 304 stainless steel base plate.
Plumbing: Complete hard plumbed process piping
• Individual fill and drain connections (at the rear utility panel) will be provided for the wash station.
• Common fill and drain connections (at the rear utility panel) will be provided for the cascade rinse stations.
• All appropriate flow control and isolation ball valves. Electrical Box: Single-point electrical connection located in an end-mounted NEMA 12 enclosure.
