2005 Tschudin HTG-400 "Swiss" Super-Precision Universal Cylindrical Grinder
GRINDERS, CYLINDRICAL_UNIVERSAL2005 Tschudin HTG-400 Rebuilt "Swiss" Super-Precision Universal Cylindrical Grinder
REBUILT & UPDATED BY "REWITECH" IN SWITZERLAND, 05/2005 **
** ACQUISITION COST IN 2005 WAS 78,500 EUROS **
Heidenhain 2X Digital Readout - Inch & Metric
Hydraulic Reservoir in Base, Isolated & Separate - Updated in 2005
Coolant System with Paper Filtration
Quick Acting Lever Type Collet Closer - Uses W25 Collets
Swing Back Diamond Wheel Dresser
"Elaso" Auto Wheel Balancing System - Model: EB200 / S/N:100828
Metric Handwheels
Rapid Course Handle for Rapid Manual Adjustment of Wheelhead Slide Position
This Machine can Accept Swing Down ID Grinding Attachment
Grinding Wheel Presently on the machine is 14" x 1.25" x 5" Bore
Dial Indicator for the Table Adjustment
Table Stop Set-Up Accessory
Electrical System Updated in 2005, Beautifully Executed
3/50/220-380 VOLT ELECTRICS
TRANSFORMER FOR 500 VOLTS TO 3/400 VOLTS, 50Hz-60Hz
** REBUILT & UPDATED BY "REWITECH" IN SWITZERLAND, 05/2005 **
Swing | 8" |
Centers | 16" |
Power | 4 hp |
Workhead Spindle Speed | 2,300 RPM |
Grinding Wheel Dia. | 14" |
Plunge (Yes/No) | Yes |
Dimensions | 60" x 48" x 58" |
Weight | 4,400 lbs |
To the best of our knowledge all details listed below are deemed correct.
It is the buyer’s responsibility to confirm all details and we encourage an inspection of the machine(s) and accessories prior to purchase.
** REBUILT & UPDATED BY "REWITECH" IN SWITZERLAND, 05/2005 **
** ACQUISITION COST IN 2005 WAS 78,500 EUROS **
www.rewitech.ch
General Specifications:
Table
Nominal Swing: 8"
Distance Between Centers: 16"
Table Speed: 0-195 IPM
Table Dwell: 0-6 Seconds
Swiveling Range: +/- 11 Degrees
Wheelhead
Wheel Size: 14" Diameter x 2"W, 5" Bore
Swiveling Range: +/- 5 Degrees
Motor: 4 HP
Spindle Speed (3): 1,640, 1,940, 2,300 RPM
Wheelhead Infeed
Range of Plunge Feed Diameter Reduction Per Minute: 0.0005" - 0.200"
Automatic Infeed of the Grinding Wheel Per Table Reversal: 0.000050"
Diameter Reduction per Rev. of Infeed Handwheel: 0.080"
Handwheel Graduation Reads to: 0.0001"
Travel by Using the Handwheel: 1.8"
Rapid Approach, Automatically: 1.5"
Movement of the Wheelhead Slide by Handwheel: 1.8"
Travel of the Wheelhead Slide Infeed, Automatically: 0-.050"
Infeed Speed: 1.2"/Min
Sparkout: 2-30 Seconds
Workhead
Spindle Taper: #5MT
Swiveling Range: 360 Degrees
Infinitely Variable Spindle Speed: 65 - 500 RPM
Tailstock
Taper of Center Bore: #3MT
Travel of Center: 0.8"
Electrics: 3/50/220-380
Transformer for 500 Volts to 3/400 Volts, 50hz-60hz
Machine Dimensions: 60" x 48" x 58"
Machine Weight: 4,400 LBS
Machine Features
Tschudin Hydrodynamic Type Cylindrical Bronze to Steel Bearing Wheelhead Design
Simple One Knob Control Initiates all the Settings for Traverse & Plunge Grinding Cycles
Hydraulic Operation Featuring:
-Power Table Traverse
-Dual Rate Infeed Option
-Plunge Infeed
-Rapid Wheelhead Advance and Retraction Sparkout Timer
Tschudin "Standard" Workhead w/ Dual Live & Dead Spindle