New Edge Minuteman 320SE Magazine Type Bar Feed

Watch the Edge Minuteman 320 operate (this unit would be configured with a
28mm (1" capacity) channel set:
http://www.youtube.com/watch?v=gfruUD-ZLks
http://www.youtube.com/watch?v=hecsV85iTcI

General Specifications As Per Brochure

Bar Diameter Capacity:
Without Prep 3mm - 21mm (0.118" - 0.8270)
With Prep 3mm - 26mm (0.118" - 1.062")
Maximum Bar Length: 12' 5"
Maximum Remnant Length: 420mm (16.5")
Magazine Rack Capacity: 10"
Bar Loading Cycle Time: 25 Seconds for 12' bar
Material Straightness Specification: .007TIR/foot of material
(V Blocks, 3 points equidistant)
Feed Force (pusher torque): max 450 N. adjustable
Forward Feed Rate: 1400 inches/min max, adjustable
Return Feed Rate: 2360 inches/min max, adjustable
Power Consumption: 1.5 kW
Operating Voltage: 230/60 Hz - 3 phase
Control Voltage: 24V DC
Oil Capacity: 46 Liters (12 gallons)
Oil Viscosity: ISO 100 cST
Compressed AirSupply: 6 bar (90 psi)
Compressed Air Consumption: approx 8 liters/loading cycle
Weight (approx): 1320 lbs
Dimensions (approx): 171" x 24" x 52"

Includes:
(1) Guide channel set matched to the lathes capacity
(1) Telescopic nose to match guide channel set
(1) O.D. bar stock pusher collet
(1) Custom lathe cable & interface plug

Minuteman 320 SE (12') $23,100.00

Minuteman 320 SE 12' 2 Guide Channel Set Complete Package $25,300.00
Includes (2) Channel Sets, (2) Pushers,
(2) Telescopic Noses & (2) Pusher Collets

Minuteman 320 SE 6': $21,100.00

Minuteman 320 6' 2 Guide Channel Set Complete Package
Includes (2) Channel Sets, (2) Pushers,
(2) Telescopic Noses & (2) Pusher Collets: $23,300.00

Optional Accessories - Prices subject to change without notice:
Installation: $3450.00

Additional guide channel set $2750.00
(includes pusher, revolving tip, standard telescopic nose and spindle liner)

Spindle liner $ 520.00
(needed when opting for a guide channel set smaller than the lathe's capacity
set)
Bar stock pusher collets $ 140.00

Moveable anti-vibration bushing blocks $ 240.00
required for profiled material, available in 8mm, 16mm & 22mm
Long Pusher Kit $1200.00

Axial Shift Device with Safety Switches $1750.00

High voltage kit $ 750
(required for some lathes)

Tall stands $1900
for lathes with spindle center greater than 1200mm

Master liner $ 650
required when undersizing barfeeder to lathe spindle (still requires spindle liner)

Minuteman 320 SE available in extended length versions

Channel Sizes

Channel Dia. Min Max Max w/
Bar Ejection

8 7.5 3mm (.118") 6.4mm (.250") 7mm (.275")
11 10 3mm (.118") 9mm (.354") 10mm (.393")
14 12 3.2mm (.125") 11mm (.437") 13mm (.512")
18 16 5mm (.196") 13.5mm (.531") 17mm (.669")
20 18 8mm (.315") 18mm (.709") 19mm (.750")
22 20 8mm (.315") 19mm (.750") 21mm (.826")
24 22 8mm (.315") 20.7mm (.817") 23mm (.905")
28 26 10mm (.395") 25.4mm (1.0") 27mm (1.062")

Bar Feeder installation does not include lathe-side software or hardware
interface. This interface must be supplied and installed by the lathe
OEM or dealer prior to bar feeder installation.

The anchoring of the bar feeder to the floor is a requirement and will be
performed by the service technician.